We have uncovered this great article relating to How to Install a Bathtub listed below on the web and think it made good sense to talk about it with you in this article.
Mounting a bathtub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard task. If the old tub is readily easily accessible, the task can relocate quickly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to think about employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will help you install a new tub in your restroom if you have already purchased a new tub and don't require to transform the setup of your previous water pipelines.
Your devices as well as product list must comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted access that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in area between the faucet and the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The former type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as readjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bathtub and likewise examine the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has been utilized at the very least when as this will settle it into its last placement.
Preparing for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface in between the bathroom and the tiling, resulting in problems with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealer can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that chunk was a smart idea. Loved our post? Please share it. Let somebody else locate it. I praise you for your time. Come back soon.
Order Repair